Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Intercooler

Pages: 1 2 [3] 4 5 ... 502
31
Hmmm... also no hits for the lower capacities?

32
  It's written a little subjective to each shooter, but I find most of it pretty spot-on. I think the Ruger should have taken more of a hit for not chambering three times. That's really critical! It seems they also dinged the Stock II some for not having a fiber front. I think they ship with one and could have been swapped preventing that loss of points.

https://www.personaldefenseworld.com/2018/01/10mm-pistol-test/

33
Gear/Equipment / Re: EAA Witness 10mm Hunter Holster
« on: January 08, 2018, 03:30:22 PM »
This is an older original Hunter, not the one offered now. Never seen one in person, but the front slide piece comes off somehow.

34
10mm semi-auto handguns / Re: Witness slide stop
« on: January 08, 2018, 03:13:27 PM »
I sent him a PM with my e-mail to host his picture. Nothing yet.

If the stop slide out to the left some it can create issues! It's best to deepen the "V" groove that goes under the spring on the right side. It fixed up my Hunter doing this!

35
10mm semi-auto handguns / Re: Witness slide stop
« on: January 07, 2018, 07:47:22 AM »
Can you take a photo with a cell phone? Has this been sliding out the left side for a bit? Need more info...

36
10mm semi-auto handguns / Re: Witness slide stop
« on: January 06, 2018, 02:10:36 PM »
  I see they indeed are a two-piece. If it were mine, I would remove the pin and apply JB Weld. Then drive it back in place and call it good.

If you bought it new hit EAA up for a replacement.

37
10mm semi-auto handguns / Re: Witness slide stop
« on: January 06, 2018, 10:21:30 AM »
I never heard of one breaking, but imagine anything is possible. I'm still on the originals in all of mine... Now CZ's seem to have an issue with them breaking though  ;)

39
10mm semi-auto handguns / Re: Witness slide stop
« on: January 06, 2018, 04:55:58 AM »
Can you take a photo? So you say you have a two-piece slide stop?

40
General Discussion / Re: Timberwolf Large Framesfor Glock 10mm
« on: January 04, 2018, 06:13:15 AM »
So what's different then? I would think the idea would be to put out something exceptional and different.

41
General Discussion / Re: Timberwolf Large Framesfor Glock 10mm
« on: January 03, 2018, 06:03:36 PM »
Still looks like a Glock  :o  ;D

42
Gunsmithing / Re: Can .38 Super be reamed to 9x25?
« on: January 03, 2018, 01:54:53 PM »
Well crap. I see not many MFG's make 9x25 ammo and probably not worth testing the couple out there.

43
Gunsmithing / Re: Can .38 Super be reamed to 9x25?
« on: January 03, 2018, 10:44:41 AM »
When it's reamed can you still shoot Super?

44
10mm semi-auto handguns / Re: Sites and Grips For Witness Elite Match
« on: January 03, 2018, 08:30:29 AM »
They will fit. Get one side secured and pull like hell! You also will need to sand the pads on the inside to clear the magazines.

45
Gunsmithing / Can .38 Super be reamed to 9x25?
« on: January 03, 2018, 06:23:11 AM »
  I think The Shadow's PC might still be down and I know he has the answer. I found this barrel for my Limited. Just want to verify and see who does this work.

Pages: 1 2 [3] 4 5 ... 502