Author Topic: Well, I think the MG20-M4 is finally complete  (Read 471 times)

DenStinett

  • Full Member
  • ***
  • Posts: 826
  • HALT, Who goes there?
    • View Profile
Well, I think the MG20-M4 is finally complete
« on: April 10, 2017, 09:13:45 PM »
Put some final touches on my MG20-M4
Have been looking for a way of covering the rear of the CCU where it is open and has an "unfinished" look to me
So I bought a 1911 CCU Front Cover
Cut, shaped and mounted it behind the Glock:


No-one would believe the GREAT deal I got, but I picked-up a FAB Defense PTK-VTS Foregrip Kit:
« Last Edit: April 11, 2017, 03:20:17 PM by DenStinett »
So tell me again how Trump will be worse then the last 8 years !

sqlbullet

  • Moderator
  • Sharpshooter
  • *****
  • Posts: 5768
    • View Profile
Re: Well, I think the MG20-M4 is finally complete
« Reply #1 on: April 11, 2017, 07:33:46 AM »
That looks very nice.

The_Shadow

  • Moderator
  • Sharpshooter
  • *****
  • Posts: 7401
    • View Profile
Re: Well, I think the MG20-M4 is finally complete
« Reply #2 on: April 11, 2017, 08:30:12 AM »
Looks great!  I agree some of the rough spots need some dressings...
The "10mm" I'm Packin', Has The Bullets Wackin', Smakin' & The Slide is Rackin' & Jackin'!
NRA Life Member
Southeast, LoUiSiAna

PCFlorida

  • Contributing Member
  • Full Member
  • ***
  • Posts: 626
    • View Profile
Re: Well, I think the MG20-M4 is finally complete
« Reply #3 on: April 12, 2017, 01:53:46 AM »
That looks great!
NRA Life Member

dred

  • Contributing Member
  • Newbie
  • ***
  • Posts: 83
    • View Profile
Re: Well, I think the MG20-M4 is finally complete
« Reply #4 on: April 12, 2017, 07:28:01 AM »
She looks well thought out.  I take it that lower is "dedicated."  Does your shoulder stock require those bolts?  Was the snap fit insufficient to secure the hand guard as dust cover?  My mechy's are both telestock'd, but I have eyes open for an appropriate piece of spring steel.

DenStinett

  • Full Member
  • ***
  • Posts: 826
  • HALT, Who goes there?
    • View Profile
Re: Well, I think the MG20-M4 is finally complete
« Reply #5 on: April 12, 2017, 11:10:09 AM »
That looks very nice.
Looks great!  I agree some of the rough spots need some dressings...
That looks great!

Thanks guys
Now to get it to the Range with the new gear



She looks well thought out.  I take it that lower is "dedicated."  Does your shoulder stock require those bolts?  Was the snap fit insufficient to secure the hand guard as dust cover?  My mechy's are both telestock'd, but I have eyes open for an appropriate piece of spring steel.
Thanks Dred
Yes, the Glock Lower is just the "receiver" for the CCU
I don't even own an Upper for it
No, the Socket Cap Screws are there to keep the Rear Cover from moving
It does snap in place, but I didn't want to chance of it popping off, so I added the Screws
Yeah, I would have preferred a Cover that would have fit under the Glock's Beavertail, instead of over it
So tell me again how Trump will be worse then the last 8 years !